- A generating station which employs gas turbine as the prime mover for the generation of electrical energy is known as a gas turbine power plant
- In a gas turbine power plant, air is used as the working fluid. The air is compressed by the compressor and is led to the combustion chamber where heat is added to air, thus raising its temperature. Heat is added to the compressed air either by burning fuel in the chamber or by the use of air heaters.
- The hot and high pressure air from the combustion chamber is then passed to the gas turbine where it expands and does the mechanical work. The gas turbine drives the alternator which converts mechanical energy into electrical energy. It may be mentioned here that compressor, gas turbine and the alternator are mounted on the same shaft so that a part of mechanical power of the turbine can be utilized for the operation of the compressor.
- Gas turbine power plants are being used as standby plants for hydro-electric stations, as a starting plant for driving auxiliaries in power plants etc.
- Advantages:
(i) It is simple in design as compared to steam power station since no boilers and their auxiliariesare required.
(ii) It is much smaller in size as compared to steam power station of the same capacity. This isexpected since gas turbine power plant does not require boiler, feed water arrangement etc.
(iii) The initial and operating costs are much lower than that of equivalent steam power station.
(iv) It requires comparatively less water as no condenser is used.
(v) The maintenance charges are quite small.
(vi) Gas turbines are much simpler in construction and operation than steam turbines.
(vii) It can be started quickly form cold conditions.
(viii) There are no standby losses. However, in a steam power station, these losses occur becauseboiler is kept in operation even when the steam turbine is supplying no load.
- Disadvantages:
(i) There is a problem for starting the unit. It is because before starting the turbine, the compressor has to be operated for which power is required from some external source. However,once the unit starts, the external power is not needed as the turbine itself supplies thenecessary power to the compressor.
(ii) Since a greater part of power developed by the turbine is used in driving the compressor, thenet output is low.
(iii) The overall efficiency of such plants is low (about 20%) because the exhaust gases from theturbine contain sufficient heat.
(iv) The temperature of combustion chamber is quite high (3000oF) so that its life is comparatively reduced.
- Schematic Arrangement of Gas Turbine Power Plant:
The schematic arrangement of a gas turbine power plant is shown in Fig. 2.9. The main components of the plant are:
(i) Compressor (ii) Regenerator (iii) Combustion chamber (iv) Gas turbine
(v) Alternator (vi) Starting motor
(i) Compressor:The compressor used in the plant is generally of rotatory type. The air at
atmospheric pressure is drawn by the compressor via the filter which removes the dust fromair. The rotatory blades of the compressor push the air between stationary blades to raise itspressure. Thus air at high pressure is available at the output of the compressor.
(ii) Regenerator:A regenerator is a device which recovers heat from the exhaust gases of theturbine. The exhaust is passed through the regenerator before wasting to atmosphere. Aregenerator consists of a nest of tubes contained in a shell. The compressed air from the compressor passes through the tubes on its way to the combustion chamber. In this way, compressed air is heated by the hot exhaust gases.
(iii) Combustion chamber:The air at high pressure from the compressor is led to the combustion chamber via the regenerator. In the combustion chamber, heat* is added to the air byburning oil. The oil is injected through the burner into the chamber at high pressure to ensure atomization of oil and its thorough mixing with air. The result is that the chamber attains a very high temperature (about 3000oF). The combustion gases are suitably cooled to 1300oF to 1500oF and then delivered to the gas turbine.
(iv) Gas turbine:The products of combustion consisting of a mixture of gases at high temperature and pressure are passed to the gas turbine. These gases in passing over the turbineblades expand and thus do the mechanical work. The temperature of the exhaust gases fromthe turbine is about 900oF.
(v) Alternator:The gas turbine is coupled to the alternator. The alternator converts mechanicalenergy of the turbine into electrical energy. The output from the alternator is given to thebus-bars through transformer, circuit breakers and isolators.
(vi) Starting motor:Before starting the turbine, compressor has to be started. For this purpose,an electric motor is mounted on the same shaft as that of the turbine. The motor is energized by the batteries. Once the unit starts, a part of mechanical power of the turbine drives thecompressor and there is no need of motor now.
Reference: –
“Power system” by V.K. MEHTA.